How to change the drill bit of an electric drill
If the drill bit of the electric drill fails, is damaged, or needs to be replaced according to the material of the hole, such as replacing the tile drill bit when drilling tiles, do you know how to change the drill bit of the electric drill? Different types of drill bits have different operation methods and replacement methods. Many friends do not know how to replace them, so this article will talk about 4 ways to replace the drill bit based on the commonly used drill bit types.
How to change the drill bit of the electric drill-hand-tight type
The drill bit position of the hand-tight electric drill is all made of steel and has a steel gear structure. Generally, this kind of hand drill will be given a "key". Insert the "key" into the small hole at the front end of the electric drill to loosen the electric drill and replace the drill bit.
Specific steps: prepare relevant tools, such as the drill bit to be replaced, electric drill key, etc.; stand the electric drill upright, hold the toothed swivel below and loosen it, and the bite mouth on the drill bit will loosen; when the bite mouth is opened to the size of the drill bit, you can insert the drill bit, and pay attention to put it in the middle of the three bite columns, and then reverse the loosened swivel so that it can bite with the drill bit rod; if the drill bit is relatively small, the electric drill bite column will extend a little when it is clamped. This is very normal; after the electric tooth ring clamps the drill bit, use the electric drill key to insert it into the small hole on the steel ring on the electric drill, and then turn the key to tighten it. This operation is required for several holes; after each hole is tightened with the electric drill key, the electric drill bit is installed. When disassembling, you must also use the electric drill key to loosen the hole.
How to change the drill bit of an electric drill-self-tightening type
Self-tightening electric drills generally use threads to fix the drill bit. The front part of the drill bit is plastic with anti-slip patterns. Hold the anti-slip textured plastic bolt at the front with your hand, preferably wearing thick gloves, then slow down the speed, press the switch, and you can grab the "three claws" of the drill bit at the front end to open it, and then put the new drill bit in, and then reverse the operation.
How to change the drill bit with an electric drill - rotating disassembly
In this comparison, the hand-tightening drill bit change is more time-consuming, and it will be even more troublesome if the electric drill key is accidentally lost. The self-tightening electric drill is more convenient and does not require an electric drill key, but it takes a lot of effort to control the drill bit, and it is easy to hurt yourself if you are not careful. There is also a convenient and quick way to replace the drill bit. The Wicks 12V lithium brushless impact drill WU131X only needs to rotate the chuck to loosen it, put the drill bit into the chuck, and then rotate the chuck to tighten it. By adjusting the tightness of the chuck, disassembly and assembly are convenient and safe.
To ensure safe use, you must ensure that the drill head and drill bit are installed in place. This Wicks WU131X impact drill chuck is 10mm Jacbos, with excellent workmanship and stable and reliable clamping. The WU131X impact drill has three modes, namely screwdriver mode, electric drill mode, and impact drill mode. Rotate the icon corresponding to the adjustment ring to the arrow position to adjust to the corresponding mode, which is simple and intuitive to operate. The 20+3 gear torque adjustment is also completed by rotating the adjustment ring. In actual use, you can choose the appropriate torque according to different working materials. In terms of speed, the maximum speed is 1800 r/min, and it supports high and low speed adjustment; the maximum torque is 40N·m, 27000 rpm high-frequency impact, supports non-load-bearing walls and lightweight concrete, so it is no problem to drill holes in brick walls and tiles on a daily basis.
There is also a snap-on drill bit. When replacing it, first turn off the power, hold the front end of the electric drill, and then push it in the direction of the grip arm to remove the drill bit. When installing the drill bit, push it to the bottom and then put it in. After releasing it, the snap will rebound and jam the drill bit. Remember to ensure the safety of the electric drill, you must ensure that the drill head and drill bit are installed in place. After installing the drill bit, you can try to operate it first to ensure that the installation is correct before starting the operation. Finally, it is recommended to save this article. The next time you encounter the problem of how to change the drill bit of an electric drill, you can refer to the operation.